15630205577产品中心
联系我们
名称：保定建兴模具制造有限公司
电话：13730205577
手机：15630205577
联系人：李经理
地址：保定市车辆管理所北行2公里路东
新闻动态
化粪池模具一般情况下选用的铁板的焊接
化粪池模具一般情况下选用的铁板的焊接，化粪池钢模具成为了最主要的生产工艺，先简单介绍一下化粪池模具，水泥化粪池主要用于楼群地下，主要用于储备生活用水，化粪池需要定时的清理，化粪池钢模具分三截，一套就是三截。
The steel mould of septic tank has become the most important production process. First, the mould of septic tank is briefly introduced. Cement septic tank is mainly used for underground buildings, mainly for reserving domestic water. The septic tank needs regular cleaning. The steel mould of septic tank is divided into three parts. It's three sections.
其实在实际生产过程中，化粪池模具也是分三截预制，对于底部来说，这种化粪池模具先预制底部，然后是中间这一截需要考虑到排水孔，同时要注意每一截的凹凸槽，
In fact, in the actual production process, the septic tank mold is also divided into three parts of prefabrication. For the bottom, this septic tank mold prefabricates the bottom first, and then the middle section needs to take into account the drainage holes, while paying attention to the concave and convex grooves of each section.
因为这个链接时保障水泥制品不错位的凹凸槽，有一截需要在地面上生产，所以需要一些凹槽，对于其他的来说都比较简单了，预制成型以后可以直接撤出内圈，等待水泥制品完全干透，就可以使用，一个楼群地下需要的化粪池数量不会太多，一般都几套，充分的保障了楼群的建设，同时也降低了劳动生产量。
Because this link guarantees that the cement products are not misaligned, there is a part of the groove that needs to be produced on the ground, so it needs some grooves. For others, it is relatively simple. After the prefabrication, the inner ring can be withdrawn directly, and the cement products can be completely dried, so it can be used. The septic needed underground for a building group can be used. The number of pools will not be too many, usually several sets, which fully guarantees the construction of the building group, but also reduces the labor production.
The steel mould of septic tank has become the most important production process. First, the mould of septic tank is briefly introduced. Cement septic tank is mainly used for underground buildings, mainly for reserving domestic water. The septic tank needs regular cleaning. The steel mould of septic tank is divided into three parts. It's three sections.
其实在实际生产过程中，化粪池模具也是分三截预制，对于底部来说，这种化粪池模具先预制底部，然后是中间这一截需要考虑到排水孔，同时要注意每一截的凹凸槽，
In fact, in the actual production process, the septic tank mold is also divided into three parts of prefabrication. For the bottom, this septic tank mold prefabricates the bottom first, and then the middle section needs to take into account the drainage holes, while paying attention to the concave and convex grooves of each section.
因为这个链接时保障水泥制品不错位的凹凸槽，有一截需要在地面上生产，所以需要一些凹槽，对于其他的来说都比较简单了，预制成型以后可以直接撤出内圈，等待水泥制品完全干透，就可以使用，一个楼群地下需要的化粪池数量不会太多，一般都几套，充分的保障了楼群的建设，同时也降低了劳动生产量。
Because this link guarantees that the cement products are not misaligned, there is a part of the groove that needs to be produced on the ground, so it needs some grooves. For others, it is relatively simple. After the prefabrication, the inner ring can be withdrawn directly, and the cement products can be completely dried, so it can be used. The septic needed underground for a building group can be used. The number of pools will not be too many, usually several sets, which fully guarantees the construction of the building group, but also reduces the labor production.
